The overall length of the Carr Bolt-On Grab Handle # CARR200042 that you referenced is 20 inches and the distance between the mounting holes on center is 19 inches. view full answer...
The Curt Trailer Hitch Receiver # C13388 will not fit your 2020 Mercedes Sprinter 3500XD with the 170" wheel base. I measured the receiver in our shop and it 33-1/2" wide between the frame rail mounting points.
We do also have the Curt Trailer Hitch Receiver # 13358 that mounts to the outside of the frame. While Curt has not been able to confirm that this will fit on an XD version of the Sprinter 3500 you can check your frame outside width to see if it has the same width. This receiver... view full answer...
According to Thule, the frame of the Thule Elite Van XT 2 Bike Rack for Sprinter Rear Door # TH302043 measures 9-7/8 inches from the mounting points to the frame. view full answer...
When we measure rise we measure from the top of the receiver opening to the top of the highest point on the slide-out platform. In this case that measurement was 6 inches. If you are measuring from the top of the outside of the receiver then it is possible that there will be interference.
But when slid out the nearest edge of the carrier will be 50 inches out measured from the center of the hitch pin hole. You can check to see, when 50 inches back from pin hole center and 6 inches up... view full answer...
Carr Custom-Fit Side Steps # CARR105771 are confirmed to fit your 2017 Mercedes-Benz Sprinter 3500 and they have a height drop of 5-inches from the mounting point on the rocker panels. The linked video will show you an example installation. The mounting hardware is included with these USA-made steps. view full answer...
Redarc does not offer longer cables between the knob and the module but we've spoken with Redarc before and they have told us that you can use a standard RJ45 network cable to extend as far as needed which you'd be able to easily source locally. The standard bracket is 1 inch wide and and is 1-1/2 inches tall with the knob being right at 3/4 inches. The harness is right at 15/16 inches wide.
The knob itself is 3/4 inches on the back 5/8 inches on the front and 1/2 inch deep. I've attached... view full answer...
The Swagman Trailhead bike rack part # S63360 has a distance of 13-7/8 inches between the arms that hold the bikes when measured from outside to outside and the frame cradles are adjustable. view full answer...
I can go ahead and give you the measurement between the bolt holes for the Curt Trailer Hitch Receiver # 13358.
As you can see by the accompanying diagram, this hitch measures 39-1/2 inches between the brackets from inside to inside, and you can use that to determine if it will fit along with the ramp on your 2018 Mercedes-Benz Sprinter 3500.
I have added a link below to the installation instructions for you to check out as well of the Curt Hitch # 13358. view full answer...
Yes, if the combination of scooter wheel base and the carrier's platform allow it you can shift the position of the scooter so that its weight is more evenly distributed on either side of the hitch tube. But I would still use the support straps # EM34415 since they will not only take up some of the weight load but also help keep the carrier and scooter steady in the hitch. view full answer...
The Curt Trailer Hitch Receiver # 13375 for your 2022 Mercedes-Benz Sprinter 3500 is 32-1/8" wide between the mounting brackets(see image). view full answer...
The 2,500 lb weight rating for the Hellwig Pro Series Helper Springs # HE47QR is a great option for your 2022 Mercedes-Benz Sprinter 3500 since motorhomes tend to have a bit more weight to them. These springs are also considered progressive so they will adjust to the amount of weight that's added to your motorhome, and your unloaded ride won't be affected.
Please note these don't add carrying capacity to your vehicle - they will just help your vehicle better handle up to 2,500 lbs. view full answer...
I apologize for any confusion but the EcoHitch Hidden Front Mount Trailer Hitch Receiver # 306-X7352 that you referenced does have a vertical weight limit of 500 lbs. view full answer...
The dimensions of the two uprights are going to be around 30 inches. It's just a bit smaller than the mounting brackets that'll be touching your Sprinter Van's doors which is 32-5/8 inches. The Thule Elite Van XT # TH302043 will leave a couple inches on each side of your van's rear door. view full answer...